Frequently Asked Question on
General Information
QiangBao® Tire Sealant has adhesive characteristics, which allows it to cling to the inner casing of the tire. This helps to prevent vibration when the tire rotates and the sealant is once again forced to flow around the tire.
When tire is stationary the sealant will pool slowly at the base of the tire. It will redistribute evenly around inside the tire once the tire is in motion.
No, QiangBao® Tire Sealant contains rust and corrosion inhibitors that protect against damage for 1 years. We recommend after 1 years you remove the sealant and replace it with new QiangBao® Tire Sealant to ensure optimal rust and corrosion protection.
As for vibration problem occurs with 4 wheelers, it is common problem for all water-based tire sealant. We tested slime, ours and other sealants, turned out all have effects on car balance when speed exceeds like 80km or 110km, depends on car type, volume installed. we have detailed test reports. for two-wheelers, not vibration issue.
So, if you are driving at high speed and the road condition is good, rarely got punctures, you do not need tire sealant pre-installed, you can have some bottle and pump stored in the car and use it when you had a flat. For those driving at moderate speed and got punctures often, pre-installation of tire sealant is really a good choice, since it saves you a lot of time and trouble.
Test result as below, for detailed test report, pls contact us.
| Test Car | Volume | Fill in | Speed | Effect |
| Nissan Sedan Car | 500ml | two front tires | 120km/h | Everything Normal |
| Nissan Sedan Car | 500ml | two rear tires | 100km/h | A little vibration. |
| Nissan Sedan Car | 500ml | Four tires | 80km/h | A little shaking |
√ Solution: use other traditional ways such as cold patch, cold bar glue or rubber strip
√ Solution: When puncture is on tire sidewall or on tire bead, please use traditional way to repair such as cold patch, cold bar glue or rubber strip.
√ Solution: Squeeze more sealant into the tire.
√ Solution: Change with a new inner tube that matches the cover tire. Before installing the tube, take a rag and wipe the inner casing of the tire to ensure there's no sealant residue, thorns, burrs or other objects protruding through the tire that might puncture the new tube, also make sure there is no kinks while installing the new tube.
√ Solution: Inflate the tire to its recommended tire pressure n' move car to a dry ground if possible, also make sure punctures is in 6 o' clock position.
√ Solution: Use other traditional ways to repair or replace the old tube.
√ Solution: Change with a new high profile tire.
√ Solution: Inflate tire to full tire pressure and drive for 2~3Km.
√ Solution: Fully shake the sealant before squeezing into tire.
QiangBao® Tire sealant is a water based liquid and therefore will evaporate faster than latex based sealant. We recommand an QiangBao® Tire sealant reinstall every 10 month, replace every 1 year.
No. The QiangBao® is actually a delivery system for fibers, rubber particles and other sealing agents. As the liquid gets forced out through the puncture, it carries along with it the larger puncture repairing ingredients which pack into and seal the hole, preventing air loss. The green/blue dot that may be visible on the outside of your tire may not harden, but may congeal, which results in a flexible seal.
QiangBao® liquid Tire sealant is non-toxic, cleans up with water and does not contain propellants. An alternate air source is required to inflate tire after installation.
Aerosol tire inflator provide minimal inflation, delivering only enough air to lift the rim off the ground and can only be used once for emergency.
Schrader is seen more as a standard “car-type” valve while the Presta valve is tapered and often found on high-end performance bicycles. QiangBao® Tire sealant can not be used to Presta valve tires.
QiangBao® Tire sealant
Seal bicycle tube puncture to 6.8mm
Motorcycle tubeless tire puncture to 10mm
Car tubeless tire puncture to 20mm
Truck tubeless tire puncture to 25mm
OTR tubeless tire puncture to 38mm
The puncture must occur in the tread area of the tire since QiangBao® cannot reach or seal punctures outside of the tread area. QiangBao® Tire sealant will not seal bead leaks or large punctures.
When QiangBao is stored in its original packaging and placed in a cool dry place it will last for 3 years. Once in the tire, QiangBao Tire Sealant will remain active for another 6 months.
When you look at the tire valve you will see a metal cylinder in the very center. This is the valve core. To install QiangBao Tire Sealant, use the black valve core removal tool on the cap of the bottle to slowly twist the core counter-clockwise. Allow the air to slowly escape before removing the core completely. After installing QB tire sealant, replace the valve core and re-inflate the tire.
QiangBao Tire Sealant is a liquid that may dry out over long periods of time. The rust and corrosion inhibitors in the sealant also break down over time. For maximum puncture protection and optimal performance, we recommended that QiangBao Tire Sealant be reinstalled every 10 months, be replaced every 1 year.
- Vehicle tire gauges, and many other types of pressure gauges are zero-referenced to atmospheric pressure, which means that they measure the pressure above atmospheric pressure which is around 1 BAR. The following key terms may be beneficial when dealing with your gauge.
- PSI (pounds per square inch) standard tire pressure reading in the USA
- KPA Kilopascal – A unit of pressure. 1 kPa is approximately the pressure exerted by a 10-g mass resting on a 1-cm2 area. 101.3 kPa = 1 atm. kPA is used as a unit of measure in Europe and other areas that use the metric system.
- BAR The BAR is a unit of pressure defined as 100 Kilopascals. It is about equal to the atmospheric pressure on Earth at sea level. 1 bar = 100 kPa (kilopascals) per square centimeter. 1 Bar = 14.50 PSI. BAR is used as a unit of measure in Europe and other areas that use the metric system.
NO, our tire sealant can not be used for built-in TPMS tire.
Please verify local waste disposal requirements. Requirements vary by county.
Generally, from our MSDS sheet, tire sealant should be diluted with large amount of water before disposal.
Our QiangBao Tire Sealant is formulated with rust and corrosion inhibitors as well as a pH buffer making the product neutral. All of these ingredients work to protect the integrity of your rim. It is important to note there are factors which can allow damage to occur in spite of this. If you want to err on the side of caution, you can use QiangBao as a roadside repair. All you need is QiangBao tire sealant and an air compressor! Despit of our advanced formula upgrade, QiangBao might have an adverse effect on certain types of aluminum rims. Because alloys differ, it is difficult to predict how QiangBao will react with your rims specifically. Over the years, though, we have found that older rims are more susceptible to damage from tire sealant. Do not leave QiangBao Tire Sealant inside your tires for more than 6 months. After that time, we cannot guarantee the integrity of your rims. If pre-existing damage is present, we do not recommend using QiangBao Tire Sealant.
We currently do sell directly from our chinese website in China. We do supply our line of products to a broad range of distributors and retailers in just about every industry (bicycle, motorcycle, ATV, lawn and garden, hardware, automotive, and industrial) in China.
For area out of China, distributors can contact us for a any kind order, sample, bulk or customized order is allways welcomed. For personal use, please ask us if there is a distributor in your country.
No. We do not recommend or guarantee our product’s performance when used in conjunction with another product.
We do not recommend nor guarantee our product for this application. Installing sealant into a wide/deep chamber without having any way to direct the sealant to the affected area would render it useless.
Suggested Volume for different vehicles (for each tire):
Bicycle: 130~250ml, Electric-Bicycle: 250ml, Scooter: 350ml, Motorcycle: 400~500ml, Car: 600~900ml.
For custom tire size, please use our volume calculator in excel sheet.
For detail, please see our volume chart and calculator.
Qiangbao tire sealant must be prefilled into the tire before puncture, when there are punctures happened to the tire tread area, under the forces from air pressure and vehicle weight, the special sealing particles (in shapes of strips, flakes, grains & powder) and filming agent rapidly rush towards the puncture, clog and block the puncture, then dry and form sealing plug, permanently seal the puncture and stop air leak.
No. We do not recommend using QB tire sealant for this purpose.
Yes. Passenger vehicle tires treated with tire sealant should be professionally repaired with an RMA approved patch/plug at your earliest convenience. Inform the shop technician that tire sealant is in the tire.
Automobile
√ Solution: use other traditional ways such as cold patch, cold bar glue or rubber strip
√ Solution: When puncture is on tire sidewall or on tire bead, please use traditional way to repair such as cold patch, cold bar glue or rubber strip.
√ Solution: Squeeze more sealant into the tire.
√ Solution: Change with a new inner tube that matches the cover tire. Before installing the tube, take a rag and wipe the inner casing of the tire to ensure there's no sealant residue, thorns, burrs or other objects protruding through the tire that might puncture the new tube, also make sure there is no kinks while installing the new tube.
√ Solution: Inflate the tire to its recommended tire pressure n' move car to a dry ground if possible, also make sure punctures is in 6 o' clock position.
√ Solution: Use other traditional ways to repair or replace the old tube.
√ Solution: Change with a new high profile tire.
√ Solution: Inflate tire to full tire pressure and drive for 2~3Km.
√ Solution: Fully shake the sealant before squeezing into tire.
Whenever possible, we recommend rotating the tire so the valve stem is in the 9 – 3 o’clock position, away from sealant that will pool at the base of the tire. This will prevent the sealant from entering the valve. Simply inflate the tire as you normally would
Whenever possible, we recommend rotating the tire so the valve stem is in the upper half of the tire, away from any sealant that may pool at the base of the tire. Then, simply inflate/deflate as you normally would.
Our QiangBao Tire Sealant is formulated with rust and corrosion inhibitors as well as a pH buffer making the product neutral. All of these ingredients work to protect the integrity of your rim. It is important to note there are factors which can allow damage to occur in spite of this. If you want to err on the side of caution, you can use QiangBao as a roadside repair. All you need is QiangBao tire sealant and an air compressor! Despit of our advanced formula upgrade, QiangBao might have an adverse effect on certain types of aluminum rims. Because alloys differ, it is difficult to predict how QiangBao will react with your rims specifically. Over the years, though, we have found that older rims are more susceptible to damage from tire sealant. Do not leave QiangBao Tire Sealant inside your tires for more than 6 months. After that time, we cannot guarantee the integrity of your rims. If pre-existing damage is present, we do not recommend using QiangBao Tire Sealant.
You shouldn’t need a tire jack unless the wheel has separated from the rim.
YES.
Motor/ATV
No. We cannot recommend or guarantee our product’s performance if added to a tire that already contains another product or liquid. If you would like to have the protection of QiangBao® Tire Sealant, you would need to remove the ballast solution and replace it with QiangBao® Tire Sealant.
No. Small punctures are an easy fix, but large gashes from glass, metal or a tear are not easy to repair. Any constant bending and flexing of the tire over rough and uneven surfaces will make it much harder for QB sealant to create a sealing plug.
Schrader is seen more as a standard “car-type” valve while the Presta valve is tapered and often found on high-end performance bicycles. QiangBao® Tire sealant can not be used to Presta valve tires.
QB tire sealant is designed for both tubeless and tube tires.
With tube tire, please be noted sealing effect is temperary lasts for days or weeks depending ton tube quanlity.
With tubeless tire, QB will seal the punctures permanently as long as your have QB tire sealant stay liquid in the tire.
Check to see if the Presta valve is two piece. If the center is removable and the valve is in fact a two piece, QiangBao® can be installed. Simply remove the core, allow the tire to completely deflate and squeeze in QiangBao®.
with Tube Tire
As for vibration problem occurs with 4 wheelers, it is common problem for all water-based tire sealant. We tested slime, ours and other sealants, turned out all have effects on car balance when speed exceeds like 80km or 110km, depends on car type, volume installed. we have detailed test reports. for two-wheelers, not vibration issue.
So, if you are driving at high speed and the road condition is good, rarely got punctures, you do not need tire sealant pre-installed, you can have some bottle and pump stored in the car and use it when you had a flat. For those driving at moderate speed and got punctures often, pre-installation of tire sealant is really a good choice, since it saves you a lot of time and trouble.
Test result as below, for detailed test report, pls contact us.
| Test Car | Volume | Fill in | Speed | Effect |
| Nissan Sedan Car | 500ml | two front tires | 120km/h | Everything Normal |
| Nissan Sedan Car | 500ml | two rear tires | 100km/h | A little vibration. |
| Nissan Sedan Car | 500ml | Four tires | 80km/h | A little shaking |
√ Solution: use other traditional ways such as cold patch, cold bar glue or rubber strip
√ Solution: When puncture is on tire sidewall or on tire bead, please use traditional way to repair such as cold patch, cold bar glue or rubber strip.
√ Solution: Squeeze more sealant into the tire.
√ Solution: Change with a new inner tube that matches the cover tire. Before installing the tube, take a rag and wipe the inner casing of the tire to ensure there's no sealant residue, thorns, burrs or other objects protruding through the tire that might puncture the new tube, also make sure there is no kinks while installing the new tube.
√ Solution: Inflate the tire to its recommended tire pressure n' move car to a dry ground if possible, also make sure punctures is in 6 o' clock position.
√ Solution: Use other traditional ways to repair or replace the old tube.
√ Solution: Change with a new high profile tire.
√ Solution: Inflate tire to full tire pressure and drive for 2~3Km.
√ Solution: Fully shake the sealant before squeezing into tire.
When QiangBao is stored in its original packaging and placed in a cool dry place it will last for 3 years. Once in the tire, QiangBao Tire Sealant will remain active for another 6 months.
Please verify local waste disposal requirements. Requirements vary by county.
Generally, from our MSDS sheet, tire sealant should be diluted with large amount of water before disposal.
Our QiangBao Tire Sealant is formulated with rust and corrosion inhibitors as well as a pH buffer making the product neutral. All of these ingredients work to protect the integrity of your rim. It is important to note there are factors which can allow damage to occur in spite of this. If you want to err on the side of caution, you can use QiangBao as a roadside repair. All you need is QiangBao tire sealant and an air compressor! Despit of our advanced formula upgrade, QiangBao might have an adverse effect on certain types of aluminum rims. Because alloys differ, it is difficult to predict how QiangBao will react with your rims specifically. Over the years, though, we have found that older rims are more susceptible to damage from tire sealant. Do not leave QiangBao Tire Sealant inside your tires for more than 6 months. After that time, we cannot guarantee the integrity of your rims. If pre-existing damage is present, we do not recommend using QiangBao Tire Sealant.
If you installed QB tire sealant to repair an existing puncture, it may not have adequately sealed on the first attempt. We recommend checking the tire for puncturing objects, removing any if found, re-inflating the tire and immediately rotating it. This forces the sealant to flow around the inner tube or tire allowing it to locate and repair the puncture. QB tire sealant is not guaranteed to seal gashes from glass or metal, bead leaks, sidewall punctures or pinch flats. Be sure to check your valve to ensure air loss is not occurring at this source.
Suggested Volume for different vehicles (for each tire):
Bicycle: 130~250ml, Electric-Bicycle: 250ml, Scooter: 350ml, Motorcycle: 400~500ml, Car: 600~900ml.
For custom tire size, please use our volume calculator in excel sheet.
For detail, please see our volume chart and calculator.
Qiangbao tire sealant must be prefilled into the tire before puncture, when there are punctures happened to the tire tread area, under the forces from air pressure and vehicle weight, the special sealing particles (in shapes of strips, flakes, grains & powder) and filming agent rapidly rush towards the puncture, clog and block the puncture, then dry and form sealing plug, permanently seal the puncture and stop air leak.
QB tire sealant is designed for both tubeless and tube tires.
With tube tire, please be noted sealing effect is temperary lasts for days or weeks depending ton tube quanlity.
With tubeless tire, QB will seal the punctures permanently as long as your have QB tire sealant stay liquid in the tire.
Check to see if the Presta valve is two piece. If the center is removable and the valve is in fact a two piece, QiangBao® can be installed. Simply remove the core, allow the tire to completely deflate and squeeze in QiangBao®.
with Tubeless Tire
As for vibration problem occurs with 4 wheelers, it is common problem for all water-based tire sealant. We tested slime, ours and other sealants, turned out all have effects on car balance when speed exceeds like 80km or 110km, depends on car type, volume installed. we have detailed test reports. for two-wheelers, not vibration issue.
So, if you are driving at high speed and the road condition is good, rarely got punctures, you do not need tire sealant pre-installed, you can have some bottle and pump stored in the car and use it when you had a flat. For those driving at moderate speed and got punctures often, pre-installation of tire sealant is really a good choice, since it saves you a lot of time and trouble.
Test result as below, for detailed test report, pls contact us.
| Test Car | Volume | Fill in | Speed | Effect |
| Nissan Sedan Car | 500ml | two front tires | 120km/h | Everything Normal |
| Nissan Sedan Car | 500ml | two rear tires | 100km/h | A little vibration. |
| Nissan Sedan Car | 500ml | Four tires | 80km/h | A little shaking |
No. Small punctures are an easy fix, but large gashes from glass, metal or a tear are not easy to repair. Any constant bending and flexing of the tire over rough and uneven surfaces will make it much harder for QB sealant to create a sealing plug.
√ Solution: use other traditional ways such as cold patch, cold bar glue or rubber strip
√ Solution: When puncture is on tire sidewall or on tire bead, please use traditional way to repair such as cold patch, cold bar glue or rubber strip.
√ Solution: Squeeze more sealant into the tire.
√ Solution: Change with a new inner tube that matches the cover tire. Before installing the tube, take a rag and wipe the inner casing of the tire to ensure there's no sealant residue, thorns, burrs or other objects protruding through the tire that might puncture the new tube, also make sure there is no kinks while installing the new tube.
√ Solution: Inflate the tire to its recommended tire pressure n' move car to a dry ground if possible, also make sure punctures is in 6 o' clock position.
√ Solution: Use other traditional ways to repair or replace the old tube.
√ Solution: Change with a new high profile tire.
√ Solution: Inflate tire to full tire pressure and drive for 2~3Km.
√ Solution: Fully shake the sealant before squeezing into tire.
QiangBao® Tire sealant
Seal bicycle tube puncture to 6.8mm
Motorcycle tubeless tire puncture to 10mm
Car tubeless tire puncture to 20mm
Truck tubeless tire puncture to 25mm
OTR tubeless tire puncture to 38mm
The puncture must occur in the tread area of the tire since QiangBao® cannot reach or seal punctures outside of the tread area. QiangBao® Tire sealant will not seal bead leaks or large punctures.
Please verify local waste disposal requirements. Requirements vary by county.
Generally, from our MSDS sheet, tire sealant should be diluted with large amount of water before disposal.
Our QiangBao Tire Sealant is formulated with rust and corrosion inhibitors as well as a pH buffer making the product neutral. All of these ingredients work to protect the integrity of your rim. It is important to note there are factors which can allow damage to occur in spite of this. If you want to err on the side of caution, you can use QiangBao as a roadside repair. All you need is QiangBao tire sealant and an air compressor! Despit of our advanced formula upgrade, QiangBao might have an adverse effect on certain types of aluminum rims. Because alloys differ, it is difficult to predict how QiangBao will react with your rims specifically. Over the years, though, we have found that older rims are more susceptible to damage from tire sealant. Do not leave QiangBao Tire Sealant inside your tires for more than 6 months. After that time, we cannot guarantee the integrity of your rims. If pre-existing damage is present, we do not recommend using QiangBao Tire Sealant.
Simply take a wet rag and wipe the area around the valve. Next, remove the valve core and use a wet cotton swab to wipe the inside of the valve and the O-rings on the valve core. Re-insert the valve core and inflate the tire.
If you installed QB tire sealant to repair an existing puncture, it may not have adequately sealed on the first attempt. We recommend checking the tire for puncturing objects, removing any if found, re-inflating the tire and immediately rotating it. This forces the sealant to flow around the inner tube or tire allowing it to locate and repair the puncture. QB tire sealant is not guaranteed to seal gashes from glass or metal, bead leaks, sidewall punctures or pinch flats. Be sure to check your valve to ensure air loss is not occurring at this source.
Yes, QiangBao® Tire Sealant can be used in any tires, but sealing performance decreas on low profile tires.
Please use QiangBao® Tire Sealant only as an emergency repair on any passenger vehicle tire. A passenger vehicle tire treated with QiangBao® Tire Sealant should be taken to a tire repair shop at your earliest convenience for a traditional repair. Please tell your repair specialist that QiangBao® Tire Sealant is in the tire.
Suggested Volume for different vehicles (for each tire):
Bicycle: 130~250ml, Electric-Bicycle: 250ml, Scooter: 350ml, Motorcycle: 400~500ml, Car: 600~900ml.
For custom tire size, please use our volume calculator in excel sheet.
For detail, please see our volume chart and calculator.
Qiangbao tire sealant must be prefilled into the tire before puncture, when there are punctures happened to the tire tread area, under the forces from air pressure and vehicle weight, the special sealing particles (in shapes of strips, flakes, grains & powder) and filming agent rapidly rush towards the puncture, clog and block the puncture, then dry and form sealing plug, permanently seal the puncture and stop air leak.
QB tire sealant is designed for both tubeless and tube tires.
With tube tire, please be noted sealing effect is temperary lasts for days or weeks depending ton tube quanlity.
With tubeless tire, QB will seal the punctures permanently as long as your have QB tire sealant stay liquid in the tire.
Aerosol Inflator
QiangBao® liquid Tire sealant is non-toxic, cleans up with water and does not contain propellants. An alternate air source is required to inflate tire after installation.
Aerosol tire inflator provide minimal inflation, delivering only enough air to lift the rim off the ground and can only be used once for emergency.
If fumes, aerosol inflator products are inhaled remove from contaminated.
Other measures are usually unnecessary.
If tire sealant or aerosol inflator is swallowed:
seek medical assistance immediately.
For more measures, please see MSDS sheet.
USAGE ↓
- Rotate puncture to 6 o' clock position.
- With Can upside down, shake Can for 30 sec. Do not remove puncturing object.
- Attach nozzle to valve.
- Keep Can upside down, take off button cap and press the button.
- Infuse aerosol inflator into tire until can is empty and rim is off the ground.
- Remove the nozzle quickly and drive for 2-3km to distribute sealant.
READ ALL CAUTIONS BEFORE USE ↓
- Use only as directed. This product is a TEMPORARY repair. Have tire inspected and repaired by a tire care professional as soon as possible to ensure safety and proper cleaning of tire pressure sensor, if so equipped. We recommend treated tire be repaired within 3 days or 100 miles after use of our product.
- Do not overinflate. Add additional air if necessary. Do not use on any vehicle with less than four tires. If used in "Z-rated" tires, be sure to check tire pressure before driving.
- This product will not repair valve leaks, sidewall punctures or punctures larger than 3mm. This product will not repair a tire that is separated from the rim.
- Keep far away from exhaust pipe when using.
STORAGE ↓
- Store can in trunk or spare tire wheel well or other cool and dry place. Do not store in vehicle interior or direct sunlight. Do not expose to heat or store at temperatures above 120°F (50°C).
PROFESSIONAL REPAIR INSTRUCTIONS ↓
- Inform tire repair specialist that tire inflator was used in tire and share warnings listed on this can.
- Do not weld or attempt repair without first removing tire from rim. Never inflate tire with pure oxygen.
- Failure to follow recommendations could result in injury and/or explosion. Expel gas in well-ventilated area before discarding.
DISPOSAL ↓
- This Product is a single-use product. Use and dispose of in accordance with state, local and federal laws and regulations.
- Do not puncture or incinerate can even after use.
- Do not place can in household trash compactor. Please recycle when empty.
WARNING ↓
- Contains gas under pressure; may burst if heated. Keep away from heat, sparks, open flames and hot surfaces.
- No smoking. May be fatal if swallowed and enters airways.
- If medical advice is needed, have product container or label at hand. Keep out of reach of children.
- Read label before use.
- IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician. Do NOT induce vomiting.
- Store locked up. Dispose of contents/container in accordance with all applicable regulations.
- Pressurized container: protect from sunlight and do not expose to temperatures exceeding 120°F(50°C).
- Do not pierce or burn, even after use. Solvent naphta (petroleum), heavy arom.
Please verify local waste disposal requirements. Requirements vary by county.
Generally, from our MSDS sheet, tire sealant should be diluted with large amount of water before disposal.
Aerosol tire inflator is designed as an emergency repair tool. It delivers only enough inflation to lift the wheel off of the road. Additional air can be added from a portable tire inflator if one is available at the time of the repair. A passenger vehicle tire that has been repaired with Aerosol tire inflator should be taken to a shop where it can be professionally and permanently repaired as soon as possible.
1. Rotate puncture to 6 o' clock position.
2. With Can upside down, shake Can for 30 sec. Do not remove puncturing object.
3. Attach nozzle to valve.
4. Keep Can upside down, take off button cap and press the button.
5. Infuse aerosol inflator into tire until can is empty and rim is off the ground.
6. Remove the nozzle quickly and drive for 2-3km to distribute sealant.
7. Drive vehicle to nearest repair shop for a permanent treatment.
Do not overinflate. Add additional air if necessary. Do not use on any vehicle with less than four tires. If used in "Z-rated" tires, be sure to check tire pressure before driving.
This product will not repair valve leaks, sidewall punctures or punctures larger than 3mm. This product will not repair a tire that is separated from the rim.
Keep far away from exhaust pipe when using.
It is possible that the sealant did not reach the puncture due to the valve not being rotated to the correct position. This is critical, especially for the larger sealant cans. The puncture should be at the 6 O’clock position, otherwise the sealant will not properly dispense.
Punctures caused by objects with diameter more than 3mm possibly not be sealed.
Tire Inflator & Pump
Usage 25L-Barrel by using pump
1. Position valve core in upper half of tire. (with valve stem at the 3:00 or 9:00 position)
2. Remove valve core with tool in cap and fully deflate the tire.
3. Remove object if there's any.
4. Using hand mixer to mix the tire sealant in the barrel evenly.
5. Install the pump into the barrel tightly, connect pump hose to the tire valve.
6. Pump the sealant into tire till suggested volume. (One down stroke of hand pump delivers 450ml of sealant, volume can be adjusted)
7. Clean up the valve, reinstall/replace the valve core and inflate the tire.
8. Drive. Stop. Verify seal and check pressure.
Repairing Tools
No! They are the same. The brown ones are easier to locate once installed into a tire because of the contrast in color.
Proper Use:
- Remove any puncturing objects.
- Insert rasp tool into hole and slide up and down to roughen and clean inside of hole.
- Remove plug material from protective backing and Insert Into eye of needle.
- Insert with plug centered in the eye of the needle into puncture until plug is pushed approximately 2/3 of the way in.
- Pull needle straight out with a rapid motion, do not twist needle while pulling out.
- Cut off excess plug material flush with the tire tread.
- Re-inflate tire to recommended pressure and test for air leaks by applying a few drops of soapy water to plugged area. If bubbles appear, repeat the process.
WARNING:
- This repair kit is only suitable emergency tire repairs to enable vehicles to be driven to a service center where proper repairs can be made to the tire.
- Not intended for use fur major tire damage.
- Radial ply passenger car tires may only be repaired in the tread area. No repairs are permitted on the bead, sidewall, or shoulder area of the tire.
- Extreme caution should be used while using tools to prevent injury; Eye protection should be worn while repairing tire.
>Remove any puncturing objects.
>Insert rasp tool into hole and slide up and down to roughen and clean inside of hole.
>Remove plug material from protective backing and insert into eye of needle.
>Insert with plug centered in the eye of the needle into puncture until plug is pushed approximately 2/3 of the way in.
>Pull needle straight out with a rapid motion, do not twist needle while pulling out.
>Cut off excess plug material flush with the tire tread.
>Reinflate tire to recommended pressure and test for air leaks by applying a few drops of soapy water to plugged area. If bubbles appear, repeat the process.
Emergency & Help
Warranties vary by tire manufacturer. Contact your tire manufacturer for specific details.
Because our tire sealant is non-toxic, the cleanup is easy. You can clean it off of any surface with a rag or a towel. We suggest you follow up with whatever cleaning product you would normally use to clean that particular surface to ensure a complete clean. We also recommend properly disposing the excess tire sealant and saturated rags after cleanup.
If this tire sealant comes in contact with eyes:
Wash out immediately with water.
If irritation continues, seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
If skin or hair contact occurs:
Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
If fumes, aerosol inflator products are inhaled remove from contaminated.
Other measures are usually unnecessary.
If tire sealant or aerosol inflator is swallowed:
seek medical assistance immediately.
For more measures, please see MSDS sheet.
If you installed QB tire sealant to repair an existing puncture, it may not have adequately sealed on the first attempt. We recommend checking the tire for puncturing objects, removing any if found, re-inflating the tire and immediately rotating it. This forces the sealant to flow around the inner tube or tire allowing it to locate and repair the puncture. QB tire sealant is not guaranteed to seal gashes from glass or metal, bead leaks, sidewall punctures or pinch flats. Be sure to check your valve to ensure air loss is not occurring at this source.